Microchip ATSAML10D14A-MU SAM L10/L11 Family Microchip IC Ultra Low-Power 32-bit Cortex-M23 MCUs with TrustZone Crypto

Features:
• Operating Conditions: 1.62V to 3.63V, -40ºC to +125ºC, DC to 32 MHz
• Core: 32 MHz (2.64 CoreMark/MHz and up to 31 DMIPS) Arm® Cortex®-M23 with:
– Single-cycle hardware multiplier
– Hardware divider
– Nested Vector Interrupt Controller (NVIC)
– Memory Protection Unit (MPU)
– Stack Limit Checking
– TrustZone® for ARMv8-M (optional)

• System
– Power-on Reset (POR) and programmable Brown-out Detection (BOD)
– 8-channel Direct Memory Access Controller (DMAC)
– 8-channel event system for Inter-peripheral Core-independent Operation
– CRC-32 generator

• Memory
– 16/32/64-KB Flash
– 4/8/16-KB SRAM
– 2-KB Data Flash Write-While-Read (WWR) section for non-volatile data storage
– 256 bytes TrustRAM with physical protection features

• Clock Management
– Flexible clock distribution optimized for low power
– 32.768 kHz crystal oscillator
– 32.768 kHz ultra low-power internal RC oscillator
– 0.4 to 32 MHz crystal oscillator
– 16/12/8/4 MHz low-power internal RC oscillator
– Ultra low-power digital Frequency-Locked Loop (DFLLULP)
– 32-96 MHz fractional digital Phase-Locked Loop (FDPLL96M)
– One frequency meter

• Low-Power and Power Management

– Active, Idle, Standby with partial or full SRAM retention and off sleep modes:
• Active mode (< 25 μA/MHz)
• Idle mode (< 10 μA/MHz) with 1.5 μs wake-up time
• Standby with Full SRAM Retention (0.5 μA) with 5.3 μs wake-up time
• Off mode (< 100 nA)
– Static and dynamic power gating architecture
– Sleepwalking peripherals
– Two performance levels

– Embedded Buck/LDO regulator with on-the-fly selection

• Security
– Up to four tamper pins for static and dynamic intrusion detections
– Data Flash
• Optimized for secure storage
• Address and data scrambling with user-defined key (optional)
• Rapid tamper erase on scrambling key and on one user-defined row
• Silent access for data read noise reduction
– TrustRAM
• Address and data scrambling with user-defined key
• Chip-level tamper detection on physical RAM to resist microprobing attacks
• Rapid tamper erase on scrambling key and RAM data
• Silent access for data read noise reduction
• Data remanence prevention
– Peripherals
• One True Random Generator (TRNG)
• AES-128, SHA-256, and GCM cryptography accelerators (optional)
• Secure pin multiplexing to isolate on dedicated I/O pins a secured communication with external
devices from the non-secure application (optional)
– TrustZone for flexible hardware isolation of memories and peripherals (optional)
• Up to six regions for the Flash
• Up to two regions for the Data Flash
• Up to two regions for the SRAM
• Individual security attribution for each peripheral, I/O, external interrupt line, and Event System
Channel
– Secure Boot with SHA-based authentication (optional)
– Up to three debug access levels
– Up to three Chip Erase commands to erase part of or the entire embedded memories
– Unique 128-bit serial number
– SAM L11 Securely Key Provisioned (KPH) (optional)
• Key Provisioning using Root of Trust flow
• Security Software Framework using Kinibi-M™ Software Development Kit (SDK)
• Advanced Analog and Touch
– One 12-bit 1 Msps Analog-to-Digital Converter (ADC) with up to 10 channels
– Two Analog Comparators (AC) with window compare function
– One 10-bit 350 kSPS Digital-to-Analog Converter (DAC) with external and internal outputs
– Three Operational Amplifiers (OPAMP)
– One enhanced Peripheral Touch Controller (PTC):
• Up to 20 self-capacitance channels
• Up to 100 (10x10) mutual-capacitance channels
• Low-power, high-sensitivity, environmentally robust capacitive touch buttons, sliders, and wheels
• Hardware noise filtering and noise signal desynchronization for high conducted immunity
• Driven Shield Plus for better noise immunity and moisture tolerance
• Parallel Acquisition through Polarity control
• Supports wake-up on touch from Standby Sleep mode
• Communication Interfaces
– Up to three Serial Communication Interfaces (SERCOM) that can operate as:
• USART with full-duplex and single-wire half-duplex configuration

• I2C up to 3.4 Mbit/s (High-Speed mode) on one instance and up to 1 Mbit/s (Fast-mode Plus) on the
second instance
• Serial Peripheral Interface (SPI)
• ISO7816 on one instance (Available on 32-pin packages only)
• RS-485 on one instance (Available on 32-pin packages only)
• LIN Slave on one instance (Available on 32-pin packages only)
• Timers/Output Compare/Input Capture
– Three 16-bit Timers/Counters (TC), each configurable as:
• One 16-bit TC with two compare/capture channels
• One 8-bit TC with two compare/capture channels
• One 32-bit TC with two compare/capture channels, by using two TCs
– 32-bit Real-Time Counter (RTC) with clock/calendar functions
– Watchdog Timer (WDT) with Window mode
• Input/Output (I/O)
– Up to 25 programmable I/O lines
– Eight external interrupts (EIC)
– One non-maskable interrupt (NMI)
– One Configurable Custom Logic (CCL) that supports:
• Combinatorial logic functions, such as AND, NAND, OR, and NOR
• Sequential logic functions, such as Flip-Flop and Latches
• Qualification and Class-B Support
– AEC-Q100 Grade 1 (-40ºC to +125ºC)
– Class-B safety library, IEC 60730 (future)
• Debugger Development Support
– Two-pin Serial Wire Debug (SWD) programming and debugging interface

Package :

About Microchip Technology

Microchip Technology Inc. is a leading provider of microcontroller and analog semiconductors, providing low-risk product development, lower total system cost and faster time to market for thousands of diverse customer applications worldwide. Headquartered in Chandler, Arizona,
Microchip offers outstanding technical support along with dependable delivery and quality.

Angel Technology Electronics Co Was Founded In HongKong Since 2006, Our branch Located In The Silicon Valley Of China, Shenzhen.Angel Technology provide one stop service for electronic components,PCB and PCB Assembly(SMT).

The Mission Of  Angel Technology Electronics Co has always been to provide Quality Electronics Components To Manufacturers Worldwide.Angel-tech's vision is become the excellent electronic components supplier with the highest satisfaction between employees and customers. Early On We became the Primary channel for project closures And Inventory build-ups for Major Distributors such as Arrow Electronics and Contract Manufacturers. Angel Technology Electronics Co Has since then added Sourcing Of High Quality Components From Local Manufacturers In China.

The corporate Philosophy Policy of  Angel Technology Electronics Co is Innovation,Not limited by the inhereent thinking,always looking for new ways to meet the needs of the market.So We have specialized in providing customers with one-stop service of electronic components, PCB and SMT since 2006, helping end customers to efficiently complete the full project including BOM list procurement process etc.

Angel Technology Electronics Co Has always been Customer Driven Rather than Opportunity Driven. Meaning- Angel Tech Will Always Choose Path That is the best For Long Term Relationship With Customer Over Short Term View. It Is Why We Have One Of The Highest Customer Retention Scores Of China Based Distributors.

Prioritizes client satisfaction:

Because of our clients are at the heart of how we work,At Angel Technology Electronic Co, our goal is to provide customers with electronic components supply,PCB production, SMT assembly one-stop service.

IInnovation and creativity:
We believe that innovation is fundamental to our success and we take particular pride in regularly working closely with industry innovators and our clients to set new standards. In recent years, Angel Technology Electronics co have also started collaborating with more and more corporations to explore new technologies in smart home and PMIC.

Inventory management:
Angel Technology Electronics co provides a third-party warehousing and professional IT inventory management software for customers to achieve seamless docking. The ownership of parts can only be transferred when the customer uses parts.

Angel Technology Electronic's incoming parts have undergone rigorous inspection, and the products are stored in standard anti-static, anti-humidity, anti-high temperature, and the stock are regularly tested to make the parts safe.

Packaging transportation standard :
The parts are tested for performance during shipment, and the packaging must be waterproof, moisture-proof and shock-proof. At the same time, Angel Technology Electronics cooperates with a number of international first-class freight companies to ensure that the parts of first- and second-tier cities can be delivered at that day, and arrive the next day. The goods of third-tier cities and remote areas can be delivered at that day and arrive within two days to ensure that customer.

Angel Technology Electronics Co have been passionated about electronic components distribute and integrated solution provider since 2006. We are also a PCBA manufacturer with our own manufacotry who can better serve for customers of smart home, communication, industry, automotive electronics and medical electronics etc.